【Reference prices · live quotation prevails】 Au Gold ▲ 786.20 ¥/g Ag Silver ▲ 9.42 ¥/g Pt Platinum ▼ 318.60 ¥/g Pd Palladium ▲ 245.80 ¥/g Rh Rhodium ▲ 1240.00 ¥/g Ir Iridium ▼ 825.50 ¥/g W Tungsten ▲ 13.20 ¥/kg Co Cobalt ▼ 198.00 ¥/kg In Indium ▲ 1620.00 ¥/kg Mo Molybdenum ▲ 285.00 ¥/kg

How to Reduce Grounding Resistance: Methods, Typical Results and Selection Criteria

Short answer: when a grounding electrode cannot reach its target resistance, the four levers that actually work are electrode depth, electrode count and spacing, low-resistivity backfill (ground enhancement material), and — in rocky or dry sites — deep-well or concrete-encased electrodes. Published field guidance puts the typical reductions at roughly 30–40% for each additional driven rod section, about 60% of single-rod resistance for two properly spaced rods, and 30–70% for bentonite, conductive-gel or conductive-grout backfill. Chemical salt treatment alone is a temporary fix and is now largely avoided because of corrosion and environmental concerns.

The design rule that saves the most money: measure soil resistivity before you design. Resistance targets and electrode quantities are both derived from it, and designing without it is the single most common cause of failed grounding acceptance tests.

About this article: published by Liaocheng Feiyan New Material Technology Co., Ltd., a Chinese manufacturer and supplier of lightning-protection and grounding materials. Ranges below are typical values compiled from IEEE Std 80 / IEEE Std 81 based design guides and Chinese national standards (GB/T 50065-2011, GB 50174-2017), retrieved 2026-10-23.

Start from the soil, not from the rod

Grounding resistance is dominated by the resistivity of the soil surrounding the electrode. Typical resistivity by soil type:

Soil typeTypical resistivity (Ω·m)Design implication
Wet clay / marshy ground10 – 100Standard driven rods usually suffice
Moist loam, humus, silt30 – 200Standard design; margin for seasonal drying
Dry sand200 – 1,000 (up to ~3,000)Deeper rods, multiple rods, enhancement backfill
Gravel and cobbles1,000 – 5,000Multiple deep rods or deep-well electrode
Solid rock / granite5,000 – 100,000+Deep-well or concrete-encased electrode; chemical treatment

Sources: IEEE Std 80-2013 based design guidance and IEEE Std 81 measurement practice; resistivity ranges as published in earthing design references, retrieved 2026-10-23. Local values must be measured — resistivity can change drastically within a few metres.

Typical resistance targets

ApplicationCommonly specified targetTypical basis
Transmission substation≤ 0.5 ΩIEEE Std 80 based utility practice
Distribution substation1 – 5 ΩIEEE Std 80 based utility practice
Heavy industrial plant≤ 1 ΩUtility / plant standard
Data centre / IT site≤ 1 ΩGB 50174-2017 (China); comparable international practice
TN distribution system≤ 4 ΩGB/T 50065-2011
TT system, general / commercial≤ 10 ΩIEC 60364 series; GB/T 50065-2011

Always confirm against the project specification and the local code having jurisdiction — targets differ by country, system type and owner.

The five reduction methods, compared

MethodHow it worksTypical reductionCost / durability notes
Drive deeperExtend the rod into moister, more compacted soil layersEach additional ~1.2 m section: ~30–40%Cheapest single action; limited by bedrock and driver capacity
Multiple rods in parallelAdd electrodes bonded together, spaced to avoid mutual interferenceTwo rods spaced ≥2.5× driven depth: ~60% of a single rod; 6–8 rods commonly reach <5 Ω in difficult soilLinear material cost; spacing is the constraint on small sites
Low-resistivity backfill (GEM)Bentonite, graphite-based or conductive compound around the electrode holds moisture and lowers contact resistanceBentonite ~30–50%; conductive gel ~40–60%; conductive grout ~50–70%Permanent if correctly specified; gel packets may need renewal on a multi-year cycle
Mesh / ring gridInterconnected horizontal conductors and rods form a large-area electrodeGrid vs single electrode: >40% (IEEE Std 80 based)Standard for substations; also controls step and touch voltage
Deep-well or concrete-encased electrodeReach deep low-resistivity strata (typically 20–30 m) or use the concrete mass as the conducting mediumConcrete-encased electrodes commonly achieve 1–5 Ω even in high-resistivity groundHighest cost; the answer for rock sites and constrained footprints

On chemical salt treatment: magnesium sulfate and similar salts give a 30–40% reduction but are temporary and corrosive. Modern practice prefers stable bentonite or graphite-based enhancement material; where any treatment is used, check it against the electrode metal for compatibility and against local environmental rules.

Measure it correctly, or you will chase the wrong problem

A grounding system that "fails" often fails because of the measurement, not the installation. The standard field method is the fall-of-potential test:

  1. Isolate the electrode under test from the installation earthing conductor, so you measure the electrode alone and not a parallel return path.
  2. Drive the current test electrode (C) in line at a distance of at least 10× the electrode depth.
  3. Place the potential electrode (P) at roughly 62% of the C distance, then repeat at several positions around that point and look for a flat (plateau) region in the readings.
  4. Record soil/model conditions — resistance rises markedly in frozen or dried-out soil, so a winter reading is not equivalent to a summer one.

Measurement method per IEEE Std 81; the 62% rule and the plateau check are what separate a trustworthy reading from a misleading one.

A practical selection sequence

  1. Measure soil resistivity and fix the target from the applicable standard.
  2. Drive deeper first — it is the cheapest reduction per unit of money.
  3. Add rods with spacing of at least 1–2× electrode length (2.5× driven depth is the commonly quoted rule) to avoid mutual resistance.
  4. Use enhancement backfill where depth is blocked by rock or the site is dry.
  5. Go to a grid, deep well or concrete-encased electrode for substations, data centres and rock sites.
  6. Verify by measurement and document the result for acceptance.

Material choice still matters

The reduction method and the electrode material are separate decisions. Copper-bonded steel gives better conductivity and a longer service life than hot-dip galvanized steel, at a higher material cost, and is generally preferred for substation and telecom work; galvanized steel remains a rational choice for general lightning-protection and cost-sensitive projects with moderate soil aggressivity. Whichever you select, use exothermic-welded or otherwise permanent connections — corroded or loose joints add contact resistance that no amount of extra rod length will fix.

Frequently asked questions

What is a good target for grounding resistance?

It depends on the application. Commonly specified targets are 4 ohms for a TN distribution system under GB/T 50065-2011, 10 ohms for a TT system, 1 ohm or less for data centres under GB 50174-2017, 1 to 5 ohms for distribution substations and 0.5 ohms or less for transmission substations under IEEE Std 80 based practice. Always confirm the project specification.

Does a longer ground rod help more than a thicker one?

Yes. Rod diameter has only a small effect — typically under 5% improvement going from 3/4 inch to 1 inch — because resistance is dominated by the surrounding soil. Rod length, rod count and soil treatment are where meaningful reductions come from.

How far apart should parallel ground rods be?

Space them at least 1 to 2 times their length, and the commonly quoted field rule is at least 2.5 times the driven depth (about 3 m minimum). Closer spacing causes the electrodes to interfere, so each additional rod delivers much less than it should.

Does ground enhancement material work permanently?

Bentonite and graphite-based compounds are designed as permanent, stable backfill and typically cut resistance by 30 to 70 percent depending on the product. Conductive gel systems may need renewal over a multi-year cycle, and salt-based chemical treatments are temporary and corrosive, so they are generally avoided in new designs.

What is the best approach for rocky ground?

Deep-well electrodes drilled 20 to 30 m into lower-resistivity strata, or concrete-encased electrodes, which commonly achieve 1 to 5 ohms even in high-resistivity ground. Multiple rods combined with enhancement backfill can also work where shallow rock permits some depth.

Why does my measured resistance change between summer and winter?

Soil resistivity is strongly dependent on moisture and temperature. Frozen or dried-out soil raises resistivity sharply, and readings in frozen ground can be several times the summer value. Measure under comparable conditions and record the season with the result.

Business inquiries:
Precious Metal Recycling · Grounding Materials · Products · Contact Us
Tel 19963594228 | Office 0635-2112001 | Email fykj425@gmail.com
← Back to News

Liaocheng Feiyan New Material Technology Co., Ltd.

Address: Room 8-1503, 15F, Building 9, Xingguang International Financial Center, Dongchang East Road, Dongcheng Sub-district, Liaocheng Economic and Technological Development Area, Shandong, China

Tel: 0635-2112001 / 19963594228 | Email: fykj425@gmail.com

Copyright © Liaocheng Feiyan New Material Technology Co., Ltd.. All Rights Reserved.

鲁ICP备2026056441号-1 | 鲁公网安备37159902000530号

⬆