Short answer: spent palladium-on-carbon (Pd/C) catalyst is almost always worth recovering, because commercial Pd/C typically carries 1–10% palladium by weight and the metal itself is not consumed by the hydrogenation reaction — it is diluted, poisoned or lost with fines. The value of a lot is set by three things: the assayed palladium content, the moisture and carbon fines fraction, and the recovery route the refinery can run. Reprocessing routes are well established: controlled incineration (or oxidative roasting) to remove the carbon carrier, reduction of any palladium oxide formed, leaching with HCl + H2O2 or aqua regia, ion-exchange purification and final refining to sponge palladium or palladium chloride.
What buyers should do first: never ship a heterogeneous catalyst lot on a "typical loading" assumption. Representative sampling plus an ICP-OES/MS assay is the only defensible basis for settlement, and the sampling plan is where most disputes start.
About this article: published by Liaocheng Feiyan New Material Technology Co., Ltd., a Chinese recycler and materials supplier handling precious and rare metal scrap. Values quoted below are typical industry ranges compiled from published process literature and refinery practice, retrieved 2026-10-23; they are engineering references, not a commercial offer.
Palladium on carbon is a supported catalyst: finely divided palladium metal dispersed on an activated-carbon carrier. It is used for hydrogenation in fine chemicals, pharmaceutical intermediates and petrochemical streams. During service the catalyst deactivates through:
Critically, deactivation does not destroy the palladium. The metal is still physically present, which is why spent Pd/C is a secondary palladium source rather than a waste.
Published commercial and process data give the following typical ranges (mass fraction, dry basis):
| Catalyst type | Typical Pd loading | Notes |
|---|---|---|
| Standard Pd/C, fine-chemicals hydrogenation | 5% – 10% | Most common commercial grades; often supplied at 5% or 10% Pd |
| Low-loaded Pd/C | 1% – 3% | Used where selectivity matters more than activity |
| PTA (purified terephthalic acid) Pd/C on coconut-shell carbon | ~0.5% | Very large-volume, low-grade stream; pre-concentration is essential |
| Incinerated / ashed residue | 10% – 50% Pd | Carbon burned off; ash enrichment depends on furnace and loss control |
| Recovered palladium chloride (PdCl2) | >59% Pd | Final refined intermediate ready for re-catalyst manufacture |
Sources: commercial catalyst grade data and published Pd/C recovery process descriptions (Chinese precious-metal refining technical literature; hydrometallurgy literature on PGM leaching), retrieved 2026-10-23. Treat as typical ranges — always confirm by assay.
| Factor | Effect on payout | How to protect yourself |
|---|---|---|
| Assay vs. nameplate loading | Large — settlement is on assayed content, not the grade you bought | Require ICP-OES/MS on a representative sample; keep a retained/sealed duplicate |
| Moisture and solvent content | Direct deduction from payable weight | Declare moisture at intake; agree the drying and weighing method in writing |
| Carbon fines and filter-aid dilution | Lowers effective Pd grade | Avoid mixing kieselguhr, filter aid or floor sweepings into the catalyst lot |
| Sulfur / halogen / heavy-metal poisoning | Adds processing cost, may trigger a treatment penalty | Declare service history and feedstock chemistry up front |
| Price reference and timing | Settlement is pegged to a published palladium reference on an agreed date | Fix the reference (e.g. an LPPM palladium price) and the pricing date in the contract |
Palladium is a volatile metal. Rather than quoting a number that will be stale within days, we settle against a published palladium reference price on an agreed date, and we state the recovery charge and treatment deduction separately so the arithmetic is auditable.
Liaocheng Feiyan New Material Technology Co., Ltd. recovers precious metals and associated rare metals from industrial secondary materials, including spent carbon-supported catalysts. Our intake protocol is sampling → assay → quoted terms → settlement on assayed contained metal, and we support lot sizes from single-drum laboratory accumulations up to bulk plant change-outs. If you have a spent Pd/C lot, the fastest path is to send photographs, the original grade specification, approximate wet weight and service history — we will tell you whether the lot justifies a full assay before anything is shipped.
Commercial Pd/C is typically supplied at 5–10% palladium, with low-loaded grades at 1–3% and some large-volume petrochemical catalysts such as PTA grades around 0.5%. The spent material is usually somewhat lower than the fresh specification because of attrition losses and dilution with fines. Only an assay on a representative sample gives a defensible number.
The carbon carrier holds the palladium and absorbs process organics, so direct leaching is slow, consumes excess reagent and leaves palladium trapped in the carbon matrix. Controlled incineration or oxidative roasting removes the carbon and concentrates the palladium roughly ten-fold, which makes the subsequent leach efficient.
Only poorly. Palladium oxide formed during high-temperature incineration is chemically inert and can resist aqua regia, which is why a liquid-phase reduction step with formic acid, formaldehyde or hydrazine is inserted before leaching to convert PdO back to metallic palladium.
Published integrated flowsheets report palladium leaching yields of about 95–98% under controlled roasting and HCl + H2O2 leaching, with overall palladium recovery above 99% in well-run plants. Your payable metal, however, is determined by the assayed content of your specific lot, not by a generic recovery percentage.
Settlement is normally the assayed contained palladium multiplied by a published palladium reference price on an agreed date, minus an agreed refining and treatment charge. Any moisture or inert dilution reduces the payable weight first. Insist that the reference price source, the pricing date and all deductions are written into the contract.
Liaocheng Feiyan New Material Technology Co., Ltd.
Address: Room 8-1503, 15F, Building 9, Xingguang International Financial Center, Dongchang East Road, Dongcheng Sub-district, Liaocheng Economic and Technological Development Area, Shandong, China
Tel: 0635-2112001 / 19963594228 | Email: fykj425@gmail.com
Copyright © Liaocheng Feiyan New Material Technology Co., Ltd.. All Rights Reserved.