Short answer: platinum-rhodium wire is one of the very few precious-metal scrap forms where the nominal alloy actually tells you something useful — and it is also the one most commonly priced wrong. On the Shanghai spot precious-metal quotes published for 26 October 2026, platinum 99.95% was quoted at 376 RMB per gram and rhodium 99.95% at 2,275 RMB per gram. Working from those two numbers, a Pt-13Rh thermocouple leg carries roughly 622.9 RMB per gram of contained metal, about 66% more than the same mass of pure platinum. Any quotation that treats this material as flat platinum gives away roughly 40% of the value.
The second thing to know is that the nominal ratio is a ceiling, not a result. Liaocheng Feiyan New Material Technology Co., Ltd. settles every lot on weighed dry mass plus measured platinum and rhodium fractions from a representative sample, each metal priced against its own benchmark, less an agreed recovery loss and refining charge.
A third point that surprises first-time sellers: on 26 October 2026 rhodium powder was quoted flat at 2,250–2,300 RMB per gram while platinum fell 4.5 RMB and gold fell 3.25 RMB. The rhodium leg of your wire did not move with the gold chart, so there is no reason to accept a quotation that has moved with it.
A standard Type S thermocouple is one pure platinum leg paired with one Pt-10Rh leg. A Type R has Pt-13Rh, and a Type B, used at the highest temperatures, pairs Pt-30Rh against Pt-6Rh. Because rhodium was trading at about six times the platinum price per gram on 26 October 2026, the alloy composition, not the weight, drives the value.
| Alloy (nominal) | Platinum share | Rhodium share | Gross metal value, RMB/g | vs. flat Pt |
|---|---|---|---|---|
| Pure platinum wire | 100% | — | 376.0 | 1.00× |
| Pt-6Rh (Type B negative leg) | 94% | 6% | 489.9 | 1.30× |
| Pt-10Rh (Type S / R positive leg) | 90% | 10% | 565.9 | 1.51× |
| Pt-13Rh (Type R positive leg) | 87% | 13% | 622.9 | 1.66× |
| Pt-20Rh | 80% | 20% | 755.8 | 2.01× |
| Pt-30Rh (Type B positive leg) | 70% | 30% | 945.7 | 2.52× |
| Pt-40Rh (glass fibre bushing alloys) | 60% | 40% | 1,135.6 | 3.02× |
Gross metal value is computed as (platinum fraction × 376 RMB/g) + (rhodium fraction × 2,275 RMB/g) using the Shanghai spot precious-metal quotes published for 26 October 2026. Recovery loss and refining charge are deducted afterwards. Figures are indicative arithmetic, not an offer.
Read the last column carefully. It is the reason a buyer who quotes one blended price for a mixed thermocouple drum is either guessing or padding, and neither of those outcomes favours the seller.
Settlement is by weighed dry mass, never by length or piece count. Wire is quoted by suppliers in metres, and installers think in metres, so the instinct is to record length. That is where disputes start: the mass per metre is a function of the square of the diameter, so a small measurement error becomes a large mass error.
| Nominal wire diameter | Approx. mass, fine platinum | Practical note |
|---|---|---|
| 0.2 mm | ~0.67 g/m | Highest surface contamination per gram; easy to lose in cutting |
| 0.3 mm | ~1.52 g/m | Thin laboratory wire, often with bead and sheath attached |
| 0.5 mm | ~4.21 g/m | The common Type S industrial gauge |
| 0.8 mm | ~10.8 g/m | Furnace and kiln installations |
| 1.0 mm | ~16.8 g/m | Heavy-duty and bushing feed wire |
Platinum-rhodium alloys are slightly less dense than fine platinum, so their mass per metre runs roughly 4–7% below the figures above at the same diameter. That difference alone is well inside the rounding that most sellers never notice, which is another reason to weigh rather than to calculate.
For scale: a metre of 0.5 mm Type S pair is roughly 8 g of wire, so a kilogram spool represents something in the order of 120 m. Whether you have 100 m or 140 m left is not knowable by looking, and at 566–623 RMB per gram the difference is material.
| Dilution source | Typical effect | What to do before shipping |
|---|---|---|
| Ceramic insulators and beads | Adds mass that assays as nothing | Strip beads; weigh wire only |
| Stainless or Inconel sheath | Can dominate the weight on sheathed probes | Split the sheath from the wire element into separate lots |
| Terminal blocks, crimp ferrules, spade lugs | Base metal carried into the sample | Cut off and settle as base metal scrap |
| Glass and enamel from bushings | Raises slag volume in melting | Declare it; do not let it arrive undeclared |
| Base-metal pickup and oxidation from service | Lowers both noble-metal fractions | Expect the assay below nominal; do not argue from the spool label |
| Moisture and cutting oil | Overstates gross weight | Settle on dry weight agreed at intake |
Submitting the lot dirty is not a problem if it is declared, because the sample then measures the dilution honestly. Submitting it dirty while expecting clean-wire pricing is where the quotation has to move.
After weighing, the wire is cleaned of obvious non-metallic attachments and either dissolved directly or homogenised by melting, depending on lot size and contamination. Noble-metal content is determined by ICP-OES or ICP-MS on solution, with fire-assay collection used where homogeneity is doubtful. Because platinum and rhodium are reported separately by ICP, this is one scrap stream where instrumental assay aligns naturally with the way the value should be split. Screening with handheld XRF is useful for confirming that you are holding Pt-Rh rather than a cheaper alloy such as Pt-Ir or a nickel-chromium lookalike, but the portable reading is not the settlement figure.
Liaocheng Feiyan New Material Technology Co., Ltd. applies the same four-step sequence to spent rhodium catalysts, described in spent rhodium catalyst recycling, and the sampling discipline is set out in PGM scrap sampling and assay. The full fee and charge structure appears in how precious metal recycling settlement works.
Take 12.00 kg of stripped Type R wire assaying at 86.4% platinum and 12.6% rhodium, with the balance base metal and refractory. Settled against the 26 October 2026 benchmarks with an agreed 97% recovery on platinum, 94% on rhodium and a refining and treatment charge of 6% of recovered metal value:
| Step | Platinum | Rhodium |
|---|---|---|
| Contained metal | 12,000 g × 0.864 = 10,368 g | 12,000 g × 0.126 = 1,512 g |
| Agreed recovery | × 0.97 = 10,057 g | × 0.94 = 1,421 g |
| Benchmark price | 376 RMB/g | 2,275 RMB/g |
| Gross recovered value | 3,781,417 RMB | 3,233,412 RMB |
| Less 6% refining charge | -226,885 RMB | -194,005 RMB |
| Net payable | 3,554,532 RMB | 3,039,407 RMB |
Total net payable: about 6,593,939 RMB. Note the shape of that result: rhodium is 12.6% of the metal but roughly 46% of the money. The arithmetic is illustrative only — recovery rates and charges are set in the contract, and the realised figure moves with the benchmark quote named for the settlement date.
Source and disclaimer: price references are Shanghai spot precious-metal quotes published for 26 October 2026, as quoted in the Chinese market note issued by Liaocheng Feiyan New Material Technology Co., Ltd. on the same date, cross-checked against the same-day Reuters gold reference of 4,009.87 USD/oz and the domestic Shanghai silver and platinum ranges. All figures here are indicative arithmetic for technical communication, not a quotation, not investment advice and not a price commitment. Actual settlement is governed by mutually accepted assay results and the signed contract. Prepared by Liaocheng Feiyan New Material Technology Co., Ltd..
It depends entirely on the rhodium fraction. At the 26 October 2026 Shanghai spot quotes of 376 RMB per gram for platinum 99.95% and 2,275 RMB per gram for rhodium 99.95%, a Pt-13Rh wire carries about 623 RMB per gram of gross metal value, roughly 65% more than the same weight of pure platinum, while a Pt-30Rh wire carries about 946 RMB per gram. Those are gross figures before recovery loss and refining charge.
No, and this is the single most expensive mistake sellers make. Pricing a Pt-13Rh leg as flat platinum at 376 RMB per gram would recognise 376 RMB against a true gross metal value of 623 RMB per gram, so roughly 40% of the lot's value is given away. The platinum leg and the platinum-rhodium leg must be assayed and priced separately.
It tells you the nominal composition, which is a starting point, not a settlement figure. After service the wire picks up base metals, oxidation and contaminants from the sheath, the bead and the terminal block, so the rhodium fraction of the metal actually recovered is usually below the nominal value. Only a sample of the specific lot can establish payable content.
Not directly, because settlement is by weighed mass rather than by length or count. Diameter matters indirectly: fine wire has far more surface area per gram, so it carries proportionally more surface contamination and loses more in cutting and handling. Typical fine platinum wire runs about 0.67 g/m at 0.2 mm and about 4.2 g/m at 0.5 mm diameter, so counting metres instead of weighing spools is unreliable.
Payable metal equals weighed dry mass multiplied by the assayed platinum fraction multiplied by the agreed platinum recovery rate, plus the same calculation carried out separately for rhodium, each priced against its own benchmark, less a refining and treatment charge agreed before shipment.
Yes, and we prefer them submitted as removed rather than pre-cleaned, because the measured dilution then appears honestly in the sample instead of being paid for as metal. Removing beads, ceramic insulators, stainless sheaths and crimp terminals before weighing raises the payable fraction and lowers the treatment charge.
Liaocheng Feiyan New Material Technology Co., Ltd.
Address: Room 8-1503, 15F, Building 9, Xingguang International Financial Center, Dongchang East Road, Dongcheng Sub-district, Liaocheng Economic and Technological Development Area, Shandong, China
Tel: 0635-2112001 / 19963594228 | Email: fykj425@gmail.com
Copyright © Liaocheng Feiyan New Material Technology Co., Ltd.. All Rights Reserved.