Bottom line: a copper-aluminum composite busbar gives switchgear and busduct designers a conductive path at >= 60% IACS with only 10-30% copper content, certified through State Grid (SGCC) testing, instead of paying for solid copper throughout the whole run. For low-voltage distribution panels, busduct trunks and outdoor switchyards where weight, installed cost and corrosion life matter, the clad conductor is often the better engineering choice. This guide explains how conductivity relates to ampacity, why joints deserve more attention than the bulk metal, and what to specify in a project supplied by Liaocheng Feiyan New Material Technology Co., Ltd. in Shandong, China.
A solid copper busbar is the reference conductor: excellent conductivity and corrosion behaviour, but heavy, expensive and increasingly exposed to theft. An all-aluminium bar is light and cheap, yet its oxide layer raises contact resistance and it needs careful surface preparation at every joint. A copper-aluminum composite busbar takes a different route: a base-metal core carries the mechanical section, while a metallurgically bonded copper-rich layer provides a stable, low-resistance conductive surface. The result keeps current near the surface where it flows, without paying solid-copper prices for the entire cross-section.
Conductivity is quoted as a percentage of the International Annealed Copper Standard (IACS). Pure copper is the 100% reference. A composite conductor certified at >= 60% IACS delivers a predictable fraction of that conductance for a given section, so ampacity is a design calculation rather than a guess. Two consequences matter in practice. First, for the same temperature-rise limit, a lower-conductivity bar generally needs a larger section than solid copper. Second, resistive loss scales with the square of current, so a conductivity shortfall is amplified on long, heavily loaded busduct runs. The correct approach is to size the bar from its certified conductivity and the actual duty cycle, then verify temperature rise under load — never to assume a clad bar is interchangeable with copper millimetre for millimetre.
In a busbar system the weakest link is almost always a joint, not the bar. Current crowding at a bolted lap, an oxide film, or uneven contact pressure raises local resistance, which creates hot spots and accelerates oxidation in a feedback loop. A bonded copper surface helps because it stays conductive and does not develop the insulating oxide that aluminium forms, so contact resistance stays stable over thermal cycles. The table summarises how the common conductor options behave at the joint.
| Conductor | Bulk conductivity | Surface / joint behaviour | Engineering note |
|---|---|---|---|
| Solid copper bar | 100% IACS reference | Stable contact; needs cleaning and torque control | Best conductor, heaviest and highest cost |
| Copper-aluminum composite bar | ≥ 60% IACS (SGCC-certified) | Bonded copper-rich surface, 10-30% copper | Good conductance per kilogram, stable contacts |
| Aluminium bar | Lower than copper | Insulating oxide; needs plating or compound | Light and low cost; joint discipline essential |
| Copper-bonded steel | around 40% IACS | Stable surface, stiff and hard to form | Standard for earth rods, less suited to complex bends |
Choose the conductor family by the job. Cables win on flexible routing and long, branching runs. Round earth rods win where the conductor must be driven into soil. A flat busbar wins where current is high, space is tight and the path is fixed — switchgear line-ups, distribution panels, busduct trunks and transformer tie-ins. In this last group a copper-aluminum composite bar is most useful: the flat section gives a large surface for heat dissipation and bolting, while the clad construction holds down weight and cost. In outdoor switchyards a corrosion-stable bonded surface also survives industrial and coastal atmospheres better than a sacrificial zinc coating.
Put five items in the purchase specification: the certified conductivity value and the testing body behind it; the copper content range and bonding method; the required section from the ampacity and temperature-rise calculation; the jointing method and surface preparation; and batch traceability. Ask for the test certificate and a batch id so delivered material can be tied back to the certified product line. For joints, control bolt torque and use the recommended preparation, then verify with a thermal scan under load. Liaocheng Feiyan New Material Technology Co., Ltd. supplies the composite conductor; final sizing must follow the project's own electrical design.
It is a flat conductor for switchgear, distribution panels and busduct, with a base-metal core for strength and a bonded copper-rich surface for stable conductivity at a lower copper content than a solid copper bar.
Not millimetre for millimetre. A composite bar is certified at 60% IACS or higher, so ampacity must be recalculated from its conductivity and checked against the allowable temperature rise before the section is fixed.
Prepare the bonded surface as recommended, keep the lap clean and flat, apply the specified bolt torque, and verify the assembled joint with a temperature-rise or thermal-image check under load.
Often yes. With a lower copper content it reduces material cost and weight, which eases handling and installation, while the stable bonded surface reduces joint maintenance and corrosion-related replacement.
Compiled by the research team of Liaocheng Feiyan New Material Technology Co., Ltd. (Liaocheng, Shandong, China), 2026-11-21. Technical figures are taken from this site's previously published material articles and the International Annealed Copper Standard, and are for engineering reference only; final sizing must follow the project's electrical design and temperature-rise verification.
Liaocheng Feiyan New Material Technology Co., Ltd.
Address: Room 8-1503, 15F, Building 9, Xingguang International Financial Center, Dongchang East Road, Dongcheng Sub-district, Liaocheng Economic and Technological Development Area, Shandong, China
Tel: 0635-2112001 / 19963594228 | Email: fykj425@gmail.com
Copyright © Liaocheng Feiyan New Material Technology Co., Ltd.. All Rights Reserved.